The tailgate is going to be just as wide and just as tall as your stock tailgate, but the lowered section is 11-1/2inches from the bottom to the top. view full answer...
The outer flange that sticks out to mount the MaxxAir MaxxFan Mini Roof Vent w/ 12V Fan - Manual Lift - 4 Speed - Smoke Item # MA00-04401M is 16-1/4" x 16-1/4" so as long as you have at least 2-1/2" to 3" of space between the panel and the cutout hole you'll have no issues. view full answer...
The Kenda 4.80/4.00-8 Bias Trailer Tire with 8" White Wheel - 5 on 4-1/2 - Load Range C # AM30060 will be approximately 6-1/2" from the lug nut hole to the ground. That will have little bearing on the tire clearance, however. The most important things to know are that it is overall 16.1" in diameter and is 4.7" wide. These numbers will be the determining factor on if you have enough clearance for the tire to fit without interfering with your fender or sidewall.
I've added a link to a... view full answer...
As long as Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118727 is installed properly the wiring will not void your warranty. You are protected under the Magnuson–Moss Warranty Act which states that manufactures cannot void the warranty of a vehicle simply because of an after-market part unless that part caused the issue.
The Tekonsha T-One wiring harness is a custom fit harness for your vehicle so it does not require splicing into the vehicle's electrical... view full answer...
The overall width of the main cross tube on the Buyers Products Class 5 Service Body Hitch Receiver # 3371801050, is 44 inches. The square cross tube is 3 inches by 3 inches, and the weld on brackets are 9-1/2 inches tall by 9 inches wide.
Check out the video I attached at the bottom of the page that goes over all these dimensions and other details of this hitch. view full answer...
In regards to the Leveling Scissor Jack Set part # JSC-24, the distance from the elongated holes from tab to tab is 6-1/4" when measuring from the center of the outside hole to the center of the other outside hole, 4-1/4" measuring from the center of the inside hole to the center of the other inside hole, and 5-1/4" when measuring from the center of the middle hole to the center of the other middle hole.
I have attached a photo to show this for you as well. view full answer...
When we installed the Curt Trailer Hitch Receiver # 13555 on a 2011 Honda CR-V, we found it has a height of 15-3/4 inches from the top of the receiver to the ground.
This is part of the formula you will use to find the correct ball mount, with the other being the height from the trailer coupler to the ground - the difference will be the rise or drop you need (if the coupler is higher you need that amount of drop; if the receiver is higher you need that amount of rise). I've added a link... view full answer...
There are a lot of different models of the SuperSprings Custom Solo Helper Springs that are available for different Ram pickups, but assuming you've got a 1500 the correct SuperSpring Custom Solo Helper Spring is part # SSR-306-47. That particular spring is 7-1/4" including bracket and is designed to replace your factory bump stop on the rear axle.
If you were looking for a different part number, just let me know and I can give you the dimension you're seeking. view full answer...
I checked with Thule for you and was able to confirm that the maximum weight capacity is 165 lbs for the Thule cargo box you asked about, which is the following part:
- Thule Force XT L # Rooftop Cargo Box TH6357B
You made a really nice choice with the Force XT, because it is not only spacious and quiet, it is also really easy to use. The box has a lid that opens from either side to make it easy to access, and once you open the lid, it stays open until you choose to close it, so you aren't... view full answer...
I can tell you how to determine the correct spindle based on your measurements, and what you will need is a digital caliper, though the first thing you need to know is the weight rating of your trailer axle. From there, what you need to do is measure your spindle to the thousandths of an inch where the bearings and grease seal ride, along with the length and diameter of your stub.
For example, the accompanying diagram shows the measurements of the #42 Spindle for 5,200 lb to 7,000 lb Trailer... view full answer...
I was able to get the dimensions you were looking for of the Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper with Pintle Mount # 3371809050.
Overall it measures 62 inches wide x 13 inches tall x 22 inches deep; also from the top of the mounting brackets to the first set of mounting holes for a pintle hook, the distance is 4 inches.
Then for a pintle hook you can choose from any of the following, which I confirmed with Buyers Products are a direct fit for the mounting plate of... view full answer...
The Dexter Shackle Bolt for Double Eye Springs # 007-126-01 measures 2-1/4" from bolt head to threaded portion. This bolt is 2-7/8" long and has a thread size of 7/16"-20. You can use Replacement 7/16"-20 Flange Nut # LC122103 with this bolt. I have attached a demonstration video for this bolt. view full answer...
The tongue weight capacity of the EcoHitch # 306-X7305 for a 2015 Mazda 3 is indeed 300 lbs. After we wrote the original product description, EcoHitch did further weight capacity testing on the # 306-X7305 hitch and found that it had a higher tongue weight capacity than originally stated.
The hitch will work great with your Mazda 3 and your 2 inch bike rack. view full answer...
I was able to confirm with my contact over at Thule that the Thule TracRac TracVan Van Ladder Rack - 2 Bar - 500 lbs # TH29055XT has an overall height from the bracket to the top of the crossbar of 13-1/4"; the distance from the bottom of the bar to the bottom of the bracket is 11-3/4", so it should provide plenty of clearance over the 8" you need. view full answer...
The mounting brackets for the 24x60 etrailer Cargo Carrier for RV Bumper - Steel - Folding - 500 lbs # e99049 are spaced apart 27.5". The carrier is going to sit away from the brackets approximately 1/2" and higher 1-1/2" to allow for enough room to fold the rack up when not in use, as you can see in the attached videos. view full answer...
The Camco UltraGuard # CAM45746 that you referenced weighs 41 lbs and is vented which prevents mildew from developing and wind lofting. view full answer...
The Axle Riser Kit - Single Square Torsion Axle # LC382741 provides a lift of 3-1/2 inches and there isn't a version that provides 6 inches of lift. view full answer...
There are no storage boxes that are confirmed to fit your 1995 Ford F-150, but I can give you the dimensions of the box you were looking at so you can verify fitment with your truck. The Du-Ha Truck Storage Box and Gun Case - Behind Seat - Black # DU20054 that you were looking at measures 50" long, 6-1/2" wide, and 6-1/2" tall according to Du-Ha. This attaches to the floor with the included hardware; drilling is required. view full answer...
I attached a diagram that shows the various dimensions of Sliding Under Platform Pontoon Boat Ladder - 3 Steps - 34-1/2" Tall - 400 lbs - Stainless Steel # 315-FOG3. The mounting brackets measure 11-7/8" long, 12" from outside edge to outside edge, and the brackets are 1-5/8" wide. I also attached a demonstration video for you. view full answer...
The overall dimensions of the # 3W-461-545-SSL-EP is 3-3/8" wide by 4-3/8" tall. The mounting holes at the top are 2-13/16" apart (green), the holes from top to bottom are 2-15/16" apart (blue line) and the bottom holes are 1-7/8" apart (yellow). view full answer...
Go To Results